View previous topic :: View next topic |
Author |
Message |
Triumph Man valued contributor
Joined: 13 Sep 2003 Posts: 1890
|
Posted: Fri May 13, 2005 1:08 pm Post subject: Gosford swapmeet |
|
|
Will be held on the 19th of june at Gosford showgrounds.
Trev
Aus
|
|
Back to top |
|
Scouse moderator
Joined: 15 Sep 2003 Posts: 5266 Location: Wollondilly, NSW
|
|
Back to top |
|
Triumph Man valued contributor
Joined: 13 Sep 2003 Posts: 1890
|
Posted: Sat May 28, 2005 9:28 am Post subject: |
|
|
I'm not sure what where going to, as funds finally run out, had to syphon one Morrie to keep the other one going this week, to many toys not enough capital.
Trev
Aus
|
|
Back to top |
|
Scouse moderator
Joined: 15 Sep 2003 Posts: 5266 Location: Wollondilly, NSW
|
|
Back to top |
|
Triumph Man valued contributor
Joined: 13 Sep 2003 Posts: 1890
|
Posted: Fri Jun 24, 2005 11:06 am Post subject: |
|
|
Sid & Tom went, I went to a club run to Peter Jacksons place. Fire museum swap this sunday & Blacktown swap next weekend, I'm after a set of 15inch sierra wheels.
I saw Rusty yesterday, showed him Russells LCV book, he said he was going to go with you, but didn't feel up to it.
Have you got Carrolla disc's , I have had 2 front left bearings go in 7 yrs, first one got noisy so I changed it, second colaspsed without warning on the way to the adalaide nationals, luck I had an old set greased up in the boot.
Going up to Roberts place know as he had a hip replacement 3 weeks ago, & he asked me to take his Van for run as it hasen't been started for ages.
Trev
Aus
|
|
Back to top |
|
Scouse moderator
Joined: 15 Sep 2003 Posts: 5266 Location: Wollondilly, NSW
|
Posted: Fri Jun 24, 2005 11:19 am Post subject: |
|
|
Trev aus wrote: | Sid & Tom went, I went to a club run to Peter Jacksons place. Fire museum swap this sunday & Blacktown swap next weekend, I'm after a set of 15inch sierra wheels.
I saw Rusty yesterday, showed him Russells LCV book, he said he was going to go with you, but didn't feel up to it.
Have you got Carrolla disc's , I have had 2 front left bearings go in 7 yrs, first one got noisy so I changed it, second colaspsed without warning on the way to the adalaide nationals, luck I had an old set greased up in the boot.
Going up to Roberts place know as he had a hip replacement 3 weeks ago, & he asked me to take his Van for run as it hasen't been started for ages.
Trev
Aus | Tarago discs, which use Holden bearings. The inner LH one decided to scream it's head off without warning while sitting on 110kph. Still had fresh grease all around it but the bearing cup is very pitted (looks like corrosion but nosign of water in the grease ).
BTW, Helles Park is on this Sunday too
|
|
Back to top |
|
Triumph Man valued contributor
Joined: 13 Sep 2003 Posts: 1890
|
Posted: Fri Jun 24, 2005 11:33 am Post subject: |
|
|
Are Tarago discs ventilated? & what bearings do you use? 30303 & 30305's
Is that swap the hotrod one?
I machined the hubs myself for the new bearings, I used a dial indicator on the old bearing surface & rotor in a 4 jaw untill they were right, but am thinking I made them a bit tight as I didn't want them to spin, maybe thats changing the shape of the cone slightly, & choping them out.
Trev
aus
|
|
Back to top |
|
Scouse moderator
Joined: 15 Sep 2003 Posts: 5266 Location: Wollondilly, NSW
|
Posted: Fri Jun 24, 2005 11:45 am Post subject: |
|
|
Ventilated - yes.
Not to sure on the numbers you've quoted Trev. I've just picked up the new set & they're LM67048/10 & LM1949/10. Supposed to be the same as Commodore bearings.
The hubs are unmodified Toyota, the stub axles are standard Holden size so everything just takes standard / easy to get bits if I'm stuck in the bush somewhere.
Hopefully this is a one off.
Hotrod swap - yes.
|
|
Back to top |
|
|